Kontakt DE
 
  BACK       FORWARD  
3.3 SINE FLUX PLATE TRONIC. E
 

  Productsearch:  


Click to see a larger image
(Illustration similar)
 

3.3.2 ETRONEE20A – „sine wave dimmer tronic.E20A, single-phase“ EN

Product Description
  • Fully electronic, single-phase sine wave dimmer (electronic regulating transformer) for ohmic-inductive and ohmic loads such as compensated or uncompensated discharge lamps, incandescent lamps, etc.
  • Optimized for use in tunnel lighting systems
  • Designed for up to 1.5 times the rated current during the lamp warm up phase (up to 10 min.)
  • Automatic lamp warm up phase when the controller is switched on
  • Regulating time delay for negative set value changes
  • Control via analogue signal or configurable default values via 3 switching contacts
  • Automatic voltage stabilisation: Mains fluctuations are compensated in dimming mode within 20 ms (if input voltage is higher than the set output voltage)
Your advantages
  • Accurate adjustment of the luminance to the actual requirements
  • Energy savings through compensation of planning reserves
  • Safety gain through possible autotracking in case of luminous flux decrease (e.g. lamp ageing)
  • Gentle operation of the lamps
  • The sinusoidal shape of the voltage is not changed, thus no mains perturbations are caused
  • Up to half the currents in the lighting system, since compensated lamps are dimmable as well
  • No moving parts that need servicing
  • High efficiency
  • Status indication via LED (operating and fault indications)
  • Parameterization via computer with software and connection cable optionally possible

Technical specifications
Electrical properties
Input voltage 230 V AC ± 10%, 47…63 Hz
Output voltage Variable between 160…230 V
(For instance dimming range of HS-lamps between ca. 30…100%)
Permanent load current 20 A any load between cos. Phi 0,3 inductive to 1,0
Control Load-independent amplitude modulation (without indirect rectifier)
Wiring Single-phase mode, star-connection with neutral wire
Device fuse Circuit breaker C20A
Analogue input signal Current signal: 4…20 mA / Voltage signal: 0…10V
or with 3 pre-parameterizable potential-free input contacts
Electrical connection All connections to the device are made via plug connectors
Control wires: Via screw terminals for cable cross sections 0.5...2.5 mm²
Load wires: Via screw terminals for cable cross sections 2.5...16 mm²
Fault signalling contact Relay  1 x change over contact, 1 A / 230 V AC, ohmic load
Output signals 2 x special function 1 x change over contact, 1 A / 230 V AC, ohmic load
1 x special function photo-MOS
Electromagnetic compatibility According to DIN EN 61326-1
Emissions: Class A – only for industrial applications
Immunity: Suitable for industrial applications
Insulation test voltage Nach EN 50 178  => aktuell: EN 62477-1:2012
   
Physical properties  
Housing Sheet steel, powder-coated
Dimensions B × H × D = 130 × 400 × 240 mm
Protection degree IP 20
Weight 11 kg
Mounting position Vertical
Cooling Forced cooling (fan is maintenance-free and exchangeable without tools)
Temperature range Storage temperature: -10°...+70° C
Ambient temperature: 0°...+50° C
 
To the Instructions: (click)

Click to see a larger image
(Illustration similar)
 

3.3.4 ETRONEE32A – „Sine wave dimmer tronic.E32A, single-phase “ EN

Product Description
  • Fully electronic, single-phase sine wave dimmer (electronic regulating transformer) for ohmic-inductive and ohmic loads such as compensated or uncompensated discharge lamps, incandescent lamps, etc.
  • Consisting of fully electronic controller tronic.E20A for power transformer operation, power transformer, system cabling and terminal block with device fuse
  • Optimized for use in tunnel lighting systems
  • Designed for up to 1.5 times the rated current during the lamp warm up phase (up to 10 min.)
  • Automatic lamp warm up phase when the controller is switched on
  • Regulating time delay for negative set value changes
  • Control via analogue signal or configurable default values via 3 switching contacts
  • Automatic voltage stabilisation: Mains fluctuations are compensated in dimming mode within 20 ms (if input voltage is higher than the set output voltage)
Your advantages
  • Accurate adjustment of the luminance to the actual requirements
  • Energy savings through compensation of planning reserves
  • Safety gain through possible autotracking in case of luminous flux decrease (e.g. lamp ageing)
  • Gentle operation of the lamps
  • The sinusoidal shape of the voltage is not changed, thus no mains perturbations are caused
  • Up to half the currents in the lighting system, since compensated lamps are dimmable as well
  • No moving parts that need servicing
  • High efficiency
  • Status indication via LED (operating and fault indications)
  • Parameterization via computer with software and connection cable optionally possible

Technical specifications
Electrical properties
Input voltage 230 V AC ± 10%, 47...63 Hz
Output voltage Variable between 165…230 V
(For instance dimming range of HS-lamps between ca. 35…100%)
Permanent load current 32 A any load between cos. Phi 0,3 inductive to 1,0
Control Load-independent amplitude modulation (without indirect rectifier)
Wiring Single-phase mode, star-connection with neutral wire
Device fuse Circuit breaker C32A
Analogue input signal Current signal: 4…20 mA / Voltage signal: 0…10V
or with 3 pre-parameterizable potential-free input contacts
Electrical connection Electronic controller tronic.E20A:
All connections pluggable, load connections pre-wired (system cable)
Control wires via screw terminals for cable cross sections 0.5...2.5 mm²
System cabling:
Load wires on the terminal block via terminals 10 mm²
Electronic controller tronic.E20A and power transformer are pluggable to the system cabling
Fault signalling contact Relay 1 x change over contact, 1 A / 230 V AC, ohmic load
Output signals 2 x special function 1 x change over contact, 1 A / 230 V AC, ohmic load
1 x special function photo-MOS
Electromagnetic compatibility According to DIN EN 61326-1
Emissions: Class A – only for industrial applications
Immunity: Suitable for industrial applications
Insulation test voltage Nach EN 50 178  => aktuell: EN 62477-1:2012
   
Physical properties  
Housing Electronic controller tronic.E20A:
Sheet steel, powder-coated
Power transformer: Insulated toroidal transformer on plastic base plate
Dimensions Electronic controller tronic.E20A: B × H × D = 130 × 400 × 240 mm
Power transformer: Æ × H = 210 × 85 mm
Terminal block: B × H × D = 60 × 80 × 80 mm
Protection degree IP 20
Weight Electronic controller tronic.E20A: 11 kg
Power transformer: 12 kg
Terminal block: 0,5 kg
Mounting position Electronic controller tronic.E20A: Vertical
Cooling Electronic controller tronic.E20A: Forced cooling (fan is maintenance-free and exchangeable without tools)
Power transformer: Natural convection
Temperature range Storage temperature: -10°...+70° C
Ambient temperature: 0°...+50° C
 
To the Instructions: (click)

Click to see a larger image
(Illustration similar)
 

3.3.6 ETRONEE40A – „ Sine wave dimmer tronic.E40A, single-phase“ EN

Product Description
  • Fully electronic, single-phase sine wave dimmer (electronic regulating transformer) for ohmic-inductive and ohmic loads such as compensated or uncompensated discharge lamps, incandescent lamps, etc.
  • Consisting of fully electronic controller tronic.E20A for power transformer operation, power transformer, system cabling and terminal block with device fuse
  • Optimized for use in tunnel lighting systems
  • Designed for up to 1.5 times the rated current during the lamp warm up phase (up to 10 min.)
  • Automatic lamp warm up phase when the controller is switched on
  • Regulating time delay for negative set value changes
  • Control via analogue signal or configurable default values via 3 switching contacts
  • Automatic voltage stabilisation: Mains fluctuations are compensated in dimming mode within 20 ms (if input voltage is higher than the set output voltage)
Your advantages
  • Accurate adjustment of the luminance to the actual requirements
  • Energy savings through compensation of planning reserves
  • Safety gain through possible autotracking in case of luminous flux decrease (e.g. lamp ageing)
  • Gentle operation of the lamps
  • The sinusoidal shape of the voltage is not changed, thus no mains perturbations are caused
  • Up to half the currents in the lighting system, since compensated lamps are dimmable as well
  • No moving parts that need servicing
  • High efficiency
  • Status indication via LED (operating and fault indications)
  • Parameterization via computer with software and connection cable optionally possible

Technical specifications
Electrical properties
Input voltage 230 V AC ± 10%, 47...63 Hz
Output voltage Variable between 165…230 V
(For instance dimming range of HS-lamps between ca. 35…100%)
Permanent load current 40 A, any load between cos. Phi 0,3 inductive to 1,0
Control Load-independent amplitude modulation (without indirect rectifier)
Wiring Single-phase mode, star-connection with neutral wire
Device fuse Circuit breaker C40A
Analogue input signal Current signal: 4…20 mA / Voltage signal: 0…10V
or with 3 pre-parameterizable potential-free input contacts
Electrical connection Electronic controller tronic.E20A:
All connections pluggable, load connections pre-wired (system cable)
Control wires via screw terminals for cable cross sections 0.5...2.5 mm²
System cabling:
Load wires on the terminal block via terminals 10 mm²
Electronic controller tronic.E20A and power transformer are pluggable to the system cabling
Fault signalling contact Relay 1 x change over contact, 1 A / 230 V AC, ohmic load
Output signals 2 x special function 1 x change over contact, 1 A / 230 V AC, ohmic load
1 x special function photo-MOS
Electromagnetic compatibility According to DIN EN 61326-1
Emissions: Class A – only for industrial applications
Immunity: Suitable for industrial applications
Insulation test voltage Nach EN 50 178  => aktuell: EN 62477-1:2012
   
Physical properties  
Housing Electronic controller tronic.E20A:
Sheet steel, powder-coated
Power transformer: Insulated toroidal transformer on plastic base plate
Dimensions Electronic controller tronic.E20A: B × H × D = 130 × 400 × 240 mm
Power transformer: Ø × H = 220 × 95 mm
Terminal block: B × H × D = 60 × 80 × 80 mm
Protection degree IP 20
Weight Electronic controller tronic.E20A: 11 kg
Power transformer: 15 kg
Terminal block: 0,5 kg
Mounting position Electronic controller tronic.E20A: Vertical
Cooling Electronic controller tronic.E20A: Forced cooling (fan is maintenance-free and exchangeable without tools)
Power transformer: Natural convection
Temperature range Storage temperature: -10°...+70° C
Ambient temperature: 0°...+50° C
 
To the Instructions: (click)

Click to see a larger image
(Illustration similar)
 

3.3.8 ETRONEE50A – „ Sine wave dimmer tronic.E50A, single-phase“ EN

Product Description
  • Fully electronic, single-phase sine wave dimmer (electronic regulating transformer) for ohmic-inductive and ohmic loads such as compensated or uncompensated discharge lamps, incandescent lamps, etc.
  • Consisting of fully electronic controller tronic.E20A for power transformer operation, power transformer, system cabling and terminal block with device fuse
  • Optimized for use in tunnel lighting systems
  • Designed for up to 1.5 times the rated current during the lamp warm up phase (up to 10 min.)
  • Automatic lamp warm up phase when the controller is switched on
  • Regulating time delay for negative set value changes
  • Control via analogue signal or configurable default values via 3 switching contacts
  • Automatic voltage stabilisation: Mains fluctuations are compensated in dimming mode within 20 ms (if input voltage is higher than the set output voltage)
Your advantages
  • Accurate adjustment of the luminance to the actual requirements
  • Energy savings through compensation of planning reserves
  • Safety gain through possible autotracking in case of luminous flux decrease (e.g. lamp ageing)
  • Gentle operation of the lamps
  • The sinusoidal shape of the voltage is not changed, thus no mains perturbations are caused
  • Up to half the currents in the lighting system, since compensated lamps are dimmable as well
  • No moving parts that need servicing
  • High efficiency
  • Status indication via LED (operating and fault indications)
  • Parameterization via computer with software and connection cable optionally possible

Technical specifications
Electrical properties
Input voltage 230 V AC ± 10%, 47...63 Hz
Output voltage Variable between 165…230 V
(For instance dimming range of HS-lamps between ca. 35…100%)
Permanent load current 50 A, any load between cos. Phi 0,3 inductive to 1,0
Control Load-independent amplitude modulation (without indirect rectifier)
Wiring Single-phase mode, star-connection with neutral wire
Device fuse Circuit breaker C50A
Analogue input signal Current signal: 4…20 mA / Voltage signal: 0…10V
or with 3 pre-parameterizable potential-free input contacts
Electrical connection Electronic controller tronic.E20A:
All connections pluggable, load connections pre-wired (system cable)
Control wires via screw terminals for cable cross sections 0.5...2.5 mm²
System cabling:
Load wires on the terminal block via terminals 16 mm²
Electronic controller tronic.E20A and power transformer are pluggable to the system cabling
Fault signalling contact Relay 1 x change over contact, 1 A / 230 V AC, ohmic load
Output signals 2 x special function 1 x change over contact, 1 A / 230 V AC, ohmic load
1 x special function photo-MOS
Electromagnetic compatibility According to DIN EN 61326-1
Emissions: Class A – only for industrial applications
Immunity: Suitable for industrial applications
Insulation test voltage Nach EN 50 178  => aktuell: EN 62477-1:2012
   
Physical properties  
Housing Electronic controller tronic.E20A:
Sheet steel, powder-coated
Power transformer: Insulated toroidal transformer on plastic base plate
Dimensions Electronic controller tronic.E20A: B × H × D = 130 × 400 × 240 mm
Power transformer: Ø × H = 230 × 100 mm
Terminal block: B × H × D = 100 × 80 × 80 mm
Protection degree IP 20
Weight Electronic controller tronic.E20A: 11 kg
Power transformer: 18 kg
Terminal block: 0,6 kg
Mounting position Electronic controller tronic.E20A: Vertical
Cooling Electronic controller tronic.E20A: Forced cooling (fan is maintenance-free and exchangeable without tools)
Power transformer: Natural convection
Temperature range Storage temperature: -10°...+70° C
Ambient temperature: 0°...+50° C
 
To the Instructions: (click)

Click to see a larger image
(Illustration similar)
 

3.3.10 ETRONEE63A – „ Sine wave dimmer tronic.E63A, single-phase“ EN

Product Description
  • Fully electronic, single-phase sine wave dimmer (electronic regulating transformer) for ohmic-inductive and ohmic loads such as compensated or uncompensated discharge lamps, incandescent lamps, etc.
  • Consisting of fully electronic controller tronic.E20A for power transformer operation, power transformer, system cabling and terminal block with device fuse
  • Optimized for use in tunnel lighting systems
  • Designed for up to 1.5 times the rated current during the lamp warm up phase (up to 10 min.)
  • Automatic lamp warm up phase when the controller is switched on
  • Regulating time delay for negative set value changes
  • Control via analogue signal or configurable default values via 3 switching contacts
  • Automatic voltage stabilisation: Mains fluctuations are compensated in dimming mode within 20 ms (if input voltage is higher than the set output voltage)
Your advantages
  • Accurate adjustment of the luminance to the actual requirements
  • Energy savings through compensation of planning reserves
  • Safety gain through possible autotracking in case of luminous flux decrease (e.g. lamp ageing)
  • Gentle operation of the lamps
  • The sinusoidal shape of the voltage is not changed, thus no mains perturbations are caused
  • Up to half the currents in the lighting system, since compensated lamps are dimmable as well
  • No moving parts that need servicing
  • High efficiency
  • Status indication via LED (operating and fault indications)
  • Parameterization via computer with software and connection cable optionally possible

Technical specifications
Electrical properties
Input voltage 230 V AC ± 10%, 47...63 Hz
Output voltage Variable between 165…230 V
(For instance dimming range of HS-lamps between ca. 35…100%)
Permanent load current 63 A, any load between cos. Phi 0,3 inductive to 1,0
Control Load-independent amplitude modulation (without indirect rectifier)
Wiring Single-phase mode, star-connection with neutral wire
Device fuse Circuit breaker C63A
Analogue input signal Current signal: 4…20 mA / Voltage signal: 0…10V
or with 3 pre-parameterizable potential-free input contacts
Electrical connection Electronic controller tronic.E20A:
All connections pluggable, load connections pre-wired (system cable)
Control wires via screw terminals for cable cross sections 0.5...2.5 mm²
System cabling:
Load wires on the terminal block via terminals 16 mm²
Electronic controller tronic.E20A and power transformer are pluggable to the system cabling
Fault signalling contact Relay 1 x change over contact, 1 A / 230 V AC, ohmic load
Output signals 2 x special function 1 x change over contact, 1 A / 230 V AC, ohmic load
1 x special function photo-MOS
Electromagnetic compatibility According to DIN EN 61326-1
Emissions: Class A – only for industrial applications
Immunity: Suitable for industrial applications
Insulation test voltage Nach EN 50 178  => aktuell: EN 62477-1:2012
   
Physical properties  
Housing Electronic controller tronic.E20A:
Sheet steel, powder-coated
Power transformer: Insulated toroidal transformer on plastic base plate
Dimensions Electronic controller tronic.E20A: B × H × D = 130 × 400 × 240 mm
Power transformer: Ø × H = 230 × 110 mm
Terminal block: B × H × D = 100 × 80 × 80 mm
Protection degree IP 20
Weight Electronic controller tronic.E20A: 11 kg
Power transformer: 19 kg
Terminal block: 0,6 kg
Mounting position Electronic controller tronic.E20A: Vertical
Cooling Electronic controller tronic.E20A: Forced cooling (fan is maintenance-free and exchangeable without tools)
Power transformer: Natural convection
Temperature range Storage temperature: -10°...+70° C
Ambient temperature: 0°...+50° C
 
To the Instructions: (click)

 1 to 5 out of 5  [ <<  1  >> ]